We are the only UK company able to offer you the “UPGRADE SMART” hardware and software upgrade for your existing BlueForce/SpeedForce gate force tester. This will give you instant display of the test results to view on your smartphone, tablet or PC (models with built in USB port only).
Category: Load & Force
New Domed Top Column Load Cell Available Now
We are very excited to introduce the smart new domed-top version of our existing column load cell which replaces the 0.25% accuracy CCD model that featured a flat top.
- Better pricing on higher capacities
- Shorter delivery times:
ONLY 4 weeks for capacities 200te and below, 5 weeks for 300 – 500te and 6 – 8 weeks for 1000te load cells. - IP67 environmental protection as standard
Single Point Load Cells Help Farmers Balance the Scales
The Challenge – Design a weighing system to accurately measure the weight of birds maximising poultry farming profitability. Poultry farmers need to accurately weigh the birds to ensure they meet the correct specification and adjust the bird feed mix accordingly.
Braking News! Applied Measurements Test Drive the New Brake Pedal Load Cell
Designed to measure brake pedal force, the CCGBP brake pedal load cell is an essential tool to the automotive industry, testing the reliability of a vehicle’s braking system with ranges from 0-50kg up to 0-200kg. This highly versatile brake pedal load cell can also be used on other pedals within the vehicle.
Weather NOT Dependent with our Compact Submersible Tension and Compression Load Cells
- Perfect for High Humidity Conditions
- Ideal for Flood Risk Locations
- Ultra Compact (Ø44mm x 65mm length)
- Fully Submersible IP68 to 10m
- Accuracy <±0.15%/Rated Capacity (0.05% typical)
- Capacities 0-250N up to 0-50kN
- Outputs: mV/V, 4-20mA, 0-10Vdc, 0-5Vdc, ±10Vdc
Applied Measurements Nominated for Automation Inside Readers’ Choice Awards 2014
Applied Measurements are proud to have been nominated for Best Automation Company of The Automation Inside Readers’ Choice Awards 2014, with our new ET24 telemetry lift link load cell chosen to run in the Best Sensor category. “We are delighted to have been nominated in not just 1 category but 2 categories of The Automation Inside Readers’ Choice Awards 2014” says Darren Skipp, Applied Measurements’ Commercial Director. “It proves that top quality products, hard work and customer commitment really do pay off”. We strongly believe that the ET24 telemetry load cell deserves this nomination thanks to its fantastic advantages: Superb Accuracy = ±0.3% of reading Transmission distances in excess of 200 metres Easy wireless monitoring from multiple locations and by […]
Versatile DSCC Pancake Load Cells Deliver Multiple Benefits
For weighing and force monitoring, Applied Measurements’ DSCC pancake load cells are the ideal choice. Here’s why….. Tension and Compression Capable Low Physical Height Complete Customisation Possible Resistant to Extraneous Forces High-Frequency Response Stainless Steel Construction The DSCC pancake load cell is designed for weighing and force monitoring alike and can operate in both tension and compression. Its low physical height lends it to applications where space is at a premium. What’s more, the DSCC pancake load cell can be entirely customised by our design team to suit your application, including the dimensions, centre thread sizes, higher capacities in excess of 3000kN and IP rating up to IP68 for submersible applications. The image above shows the recent customisation of the […]
Telemetry Lift Link Load Cells Tip the Scales for Plaxton Bus
A multi-channel system was set up using two ET24-5T and two ET24-12T telemetry lift link load cells, two inclinometers (angle sensors) and a T24-BSu base station. ET24 telemetry load cells were attached to each corner of the bus to monitor the load and the two inclinometers were used to measure the incline. Once the bus was lifted, instantaneous measurements were picked-up by a T24-BSu wireless telemetry base station and the data was transmitted straight to the PC or laptop.
